Built-In Ultrasonic Measurement
Turn Periodic Vibration Measurements Into Automated Monitoring
Machine health can change between inspections.
The Wi-care™ 300 closes these monitoring gaps by automatically collecting vibration data from third-party wired sensors at configurable intervals, helping spot changes in asset health earlier and giving your team more time to act.
Leverage Existing Third-Party Wired Sensors
Automate Vibration Data Collection
Detect Changes in Asset Health Earlier
Gain More Time to Plan Maintenance
I-DNA Powered
Built-In Ultrasonic Capabilities
Our Wi-care™ 300 captures micro-impacts and high-frequency signals. They reveal production killers that conventional vibration analysis would often miss.
By picking up these signals earlier, Wi-care™ 300 gives maintenance teams more time to investigate and address issues before they disrupt production.
High-Frequency Vibration Monitoring
Our I-DNA technology picks up micro-impacts that can reveal early signs of wear and faults that conventional vibration analysis can miss.
BPFO
BPFI
Bearing
wear
Bearing
erosion
Cavitation
Gear
defects
Severe
sliding
Articulating
machines
Electrical
equipment
Reciprocating
machines
Low RPM
machines
Stick-slip
friction
Standard Vibration Monitoring
Wi-care™ also identifies common machine faults by tracking changes in vibration patterns.
Unbalance
Misalignment
Belt
problems
Bent
shaft
Resonance
Soft
foot
Belt
wear
Blade
passage
Vane
passage
Shaft
eccentricity
Stator/Rotor
eccentricity
Rubbing
Rotating
looseness
Structural
looseness
Wireless Monitoring Where You Need It
Wi-care™ 300 Applications
Keep your existing wired vibration sensors or install new ones where directly mounted wireless sensors aren’t suitable.
Existing Wired Sensors
Reuse compatible wired vibration sensors already installed on equipment to automate data collection without unnecessary sensor replacement.
Extreme Heat
Monitor equipment exposed to high temperatures using appropriately rated wired sensors while keeping the Wi-care™ 300 away from excessive heat.
Enclosed Machines
Install wired sensors inside metallic enclosures that restrict wireless signals, while positioning the Wi-care™ 300 outside to enable wireless communication.
Hard-to-Reach Areas
Install wired sensors at difficult-to-access measurement points while positioning the Wi-care™ 300 in a more accessible location.
Washdown Areas
Use washdown-rated wired sensors in areas requiring intensive cleaning while positioning the Wi-care™ 300 away from direct exposure to water and cleaning chemicals.
Poor Wireless Coverage
Install wired vibration sensors where wireless connectivity is limited or unavailable, and position the Wi-care™ 300 where it can communicate reliably with the I-care network.
Connect Vibration Monitoring
to Machine Operation
The Wi-care™ 300 features an auxiliary I/O interface supporting 4–20 mA signals and 24 V input/output (max. 100 mA) for connecting a tachometer or compatible grease pump.
Beyond automated vibration data collection, this connectivity enables measurements to respond to machine operation, supports more accurate analysis, and opens the door to condition-based lubrication.
Machine-Start Triggering
Automatically trigger vibration measurements when equipment starts, capturing data when the machine is operating.
Four-Channel Synchronization
Synchronize vibration measurements across all four connected sensor channels to capture machine behavior at the same time.
Variable-Speed Analysis
Use tachometer signals to track changes in rotational speed and improve vibration analysis on variable-speed equipment.
Condition-Based Lubrication
Connect a compatible grease pump to automatically deliver grease based on bearing condition and analyze the bearing’s response after lubrication to determine whether additional greasing is needed.
Dive Into the Wi-care™ 300 Specs
Third-Party Connectivity
Connect your IEPE and low-power third-party wired vibration sensors to the Wi-care™ 300, whether they’re already installed or part of a new installation.
Four Measurement Points
Connect up to 4 wired vibration sensors to a single Wi-care™ 300 to automatically collect vibration data from multiple measurement points on your equipment.
Ultrasonic Data Acquisition
Capture the high-frequency vibration signals required for I-care’s patented I-DNA™ analysis, helping your team detect developing defects earlier.
Up to 5 Years of Battery Life
Benefit from up to 5 years of battery operation on a standard measurement cycle, thanks to patented power management. A 12–24 VDC power supply is also available.
Datasheet
Explore the Wi-care™ 300’s technical specifications, including sensor compatibility, measurement capabilities, and battery life.
Download the datasheet for the details you need to assess connectivity, compare power options, and plan your installation.
Wi-care™ 300 Monitoring Setup
The Wi-care™ 300 seamlessly connects third-party sensors to the I-care ecosystem, bringing its full monitoring and analytics capabilities to your machines.
Third-Party Wired Sensors
Measure vibration at the machine using IEPE or low-power sensors.
Wi-care™ 300
Acquires data from the sensors and transmits it wirelessly to the Gateway.
I-care Gateway
Receives data wirelessly from the Wi-care™ 300 and forwards it to I-see™.
I-see™ AI-powered Platform
Analyzes vibration data to identify developing faults.
Connect to the
I-care Ecosystem
Explore I-care technologies and services that connect machine-condition monitoring, analysis, and maintenance action.
Inside the I-care Factory That Builds the Wi-care™ 300
We develop and manufacture the Wi-care™ 300 at our own factory. With I-care R&D and production teams under one roof, we can turn feedback into product improvements, oversee testing directly, and track each device through production.
Continuous Innovation
Consistent Product Quality
Full Traceability
Greater Control Over Delivery
Let’s Clear Things Up
Wi-care™ 300 FAQ
What is the Wi-care™ 300 and how does it work?
The Wi-care™ 300 is a wireless vibration data acquisition device that connects up to 4 third-party wired vibration sensors to the I-care ecosystem. It automatically acquires vibration data at configurable intervals and transmits it wirelessly through an I-care Gateway to I-see™ for condition monitoring and analysis.
What is the difference between the Wi-care™ 300 and Wi-care™ 130?
- The Wi-care™ 300 enables automated wireless monitoring with third-party wired vibration sensors, making it particularly suited to existing installations or applications where directly mounted wireless sensors aren’t suitable, such as high-temperature environments, enclosed machines, or areas with poor wireless coverage.
- The Wi-care™ 130 combines vibration sensing and wireless communication in one device and is recommended for most new applications where direct sensor mounting is appropriate.
- Both devices are complementary and can be used together within the same I-care ecosystem.
Which vibration sensors are compatible with the Wi-care™ 300?
The Wi-care™ 300 supports third-party wired IEPE and low-power vibration sensors, whether already installed or added as part of a new installation.
Can the Wi-care™ 300 be used with existing wired vibration sensors?
Yes. You can connect existing wired vibration sensors to the Wi-care™ 300 to automate data collection and enable wireless condition monitoring without replacing sensors that already meet your application requirements.
What equipment is needed for a Wi-care™ 300 monitoring setup?
A Wi-care™ 300 monitoring setup requires compatible third-party wired vibration sensors, a Wi-care™ 300 acquisition device, an I-care Gateway, and access to I-see™. The sensors measure vibration, the Wi-care™ 300 acquires and transmits the data wirelessly through the Gateway, and I-see™ performs AI-powered analysis.
How is the Wi-care™ 300 powered and how long does the battery last?
The Wi-care™ 300 operates on battery power or a 12–24 VDC supply. Patented power management enables up to 5 years of battery operation on a standard measurement cycle.
Bring Automated Wireless Monitoring to Your Wired Sensors
Whether you’re working with existing wired sensors or planning a new installation, our experts can help you determine how the Wi-care™ 300 fits your equipment and monitoring requirements.
